Full HD Mini Spy Camera Instructions

Full HD Mini Spy Camera

The Full HD Mini Spy Camera is a compact and discreet device with a size of only 2,9 cm that allows you to capture high-quality images and videos easily and efficiently. Equipped with integrated microphone allowing you to capture the sound of the environment. Includes recording with night vision and function of wifi real time transmission in the version with wifi included.

Technical characteristics

Resolution of Full HD with great quality reproduction of colors and sharpness. You will be able to observe every movement captured by the camera.

Capture images or videos of quality with integrated microphone y night vision with 2 infrared LEDs and the LDR-sensor (Light Dependent Resistor)

The files in AVI format They are stored on a microSD (not included) in the camera. Supports microSD from 2GB to 128GB (minimum Class 10).

The function of Wi-Fi streaming allows you to view the camera in real time through the HDWifiCamPro application for IOS/Android and record in the cloud.

The camera includes a built-in rechargeable battery 500mAh. This battery can be 100% charged in 2 hours and offers up to 4 hours of recording.

Content

Full HD Mini Spy Camera /Wifi

Magnetic Camera Support

3M adhesive

Semi-rigid Flexible Charging Cable

USB Charging and Transfer Cable

Manual

Instructions

Step 1 - Load

The battery is shipped with a low charge. It must of charge with a USB charger.

The camera emits a red light (SD version) or green (Wifi version) flashing while charging that stays on when it reaches 100%.

El charging time is about 2 hours when connected to a 1 amp charger at 5 Volts (Maximum 5V 2.0A, using more amperage will reduce the life of the camera's built-in battery).

The camera can be charged while on, but it will increase the loading time. It is also possible use the camera always connected to the charge (not while connected to a computer via USB).

Step 2 - MicroSD

Introduce before ignition MicroSD into the slot until you hear a click. It is recommended to format the card to FAT 32 format and use a card with a Class 10 transfer speed. The minimum size allowed is 2 GB and the maximum 128 GB.

Step 3 - Power On/Off and Recording

ATTENTION - It is normal for the camera to get hot during use.. It is a matter of chip design and does not affect its operation.

Select your Camera Model

Step 3.1 - Version Without Wifi

Turn on the camera holding down the power button for 3 seconds. This button has the function of on/off, mode change and start/stop recording. At power up, el Steady Blue LED will indicate that the camera is in Standby Mode and Continuous Recording Mode. If they turn on the Blue and Red LED flashing there is no microSD inserted or it is not being detected. The camera will turn off after a few seconds if this occurs.To start recording press the power button once, Blue LED will flash twice and it will turn off indicating that recording has started. For stop recording press the power button once again and the Blue LED will remain steady indicating that the recording has been stopped and saved, and that we have returned to standby mode. The videos are separated for security in 5 minute long videos and when the battery runs out it is automatically saved.To turn it off, press and hold the on/off button for 6 seconds.

FOR activate motion detection mode, while the camera is on and in standby mode with the Steady blue LED, press and hold the power button for 2 seconds. El Red LED will flash 2 times and recording will start by motion detection.

FOR stop recording press the power button once, the Blue LED will remain steady indicating that the recording has been stopped and saved, and that we have returned to standby mode.

La night vision activates automatically when the LDR (Light Dependent Resistor) sensor detects low luminosity.

Step 3.2 - Version With Wifi

Turn on the camera holding down the power button for 3 seconds. This button has the function of on/off, mode change and start/stop recording.

On ignition The LED will indicate the status of the camera:

Flashing Blue LED – Slow + Red LED – Steady: Waiting for Wi-Fi configuration.
Blue LED – Steady + Red LED – Steady: Connected to a configured Wi-Fi network, allows remote viewing.
Blue LED Flashing – Fast + Red LED – Steady: Searching for the Wi-Fi network to which it has been configured.

FOR turn it off, press and hold the on/off button for 6 seconds.

Step 4 - Watermark

To modify the watermark on videos, connect the microSD to a computer and open the TIME.txt file.

We can adjust the date and time of the watermark. For example, if we want to indicate the date 10/06/2023 and time 12:00, we will modify the first line of text to:

And 2023061000000

In addition, we can activate/deactivate the mark of water changing between Y (activated) or N (deactivated).

Remember save the changes to the file.

Step 5 - Wifi Remote Viewing

Step 5.1 - Application Download

Download the HDWifiCamPro app on your mobile by pressing the Android or App Store (iPhone) icon depending on the model of your device.

Step 5.2 - Application and Permissions

Open the HDWifiCamPro application and grant all required permissions in the app.

It will also be necessary to accept the app's user agreement upon first use.

Step 5.3 - Wifi connection

Turn on the camera by pressing the power button and wait at least 10 seconds for the camera to turn on. When the camera's Wifi is activated, A blue LED will flash slowly and the red LED will be steady.. Next, access the mobile's Wi-Fi settings and connect to the DGK-XXXXXX-XXXXX Wi-Fi network. If a notice appears when connecting indicating that this Wi-Fi network does not have internet and showing the option to maintain the connection or disconnect it, we must mkeep the connection.

Step 5.4 - Configuration

Open the app and the camera to which we have connected via Wifi will appear on the main screen.

PClick on the gear icon and click on “WiFi Settings”.

Select the Wi-Fi network (2.4 GHz type) to which the camera is to be connected.

Enter the password for the Wi-Fi network and click “Yes”.

We will return to the main screen and a notice will appear indicating that the camera is being configured. The camera will reboot and turn off your wifi network DGK-XXXXXX-XXXXX.

EThe mobile must connect to the internet again using a Wi-Fi network or mobile data and we must wait for the camera to show the fixed blue and red light indicating that it has been configured correctly.

Now, Click on the camera on the main screen of the app and the “Online” status should appear and we can view the camera remotely.

If the blue and red LEDs do not remain steady, it indicates that the configuration is incorrect. We must factory reset the camera as indicated in step 6 and repeat the configuration, checking the Wi-Fi network password and preventing it from having special or strange characters..

Step 5.5 - Settings

Click on the icon in the upper right corner to modify the settings such as motion detection, date and time setting (automatically adjusted when pairing the camera in the app), the microSD configuration or modify the Wi-Fi network name and password.

Step 6 - Reset

If the camera is failing, the setup has failed or we want to restore factory settings, press the reset button while it is on and hold the button for at least 6 seconds. The camera will turn off the red LED and then the red LED will turn on again and the blue LED will start flashing.

It is advisable to access the app and in the configuration gear wheel click on «Delete» so that the camera is deleted from the app and we can configure it again.

If you have questions, don't hesitate to contact us! 😉

Frequent Problems

1 - Does not turn on

The battery is shipped with a low charge. It must of charge with a USB charger.

The camera emits a red or green light flashing while charging that stays solid when it reaches 100%.

El charging time is about 2 hours when connected to a 1 amp charger at 5 Volts (Maximum 5V 2.0A, using more amperage will reduce the life of the camera's built-in battery).

The camera can be charged while on, but it will increase the loading time. It is also possible use the camera always connected to the charge (not while connected to a computer via USB).

2 - Does not store

Enter the microSD into a computer and check that you can read it.

La microSD it is recommended that you have FAT32 format.

Remember to use a microSD between 32 and 128GB and that the transfer speed is minimum 10 Class.

If you have questions, don't hesitate to contact us! 😉

Security and Compliance

Below is indicated important product information in relation to the security and compliance that guarantee proper and safe use of the product:

⚠ FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN FIRE, ELECTRIC SHOCK, OR OTHER DAMAGE OR INJURY.

Product specifications:

Model Name: Full HD Mini Spy Camera

Model Number:CE-05/06

Product identifier: 706212918430

Product battery: Integrated Lithium-Ion type with 500 mAh capacity

Operating temperature: 0 to 50ºC

Product Use: Do not expose your device or adapter to liquids. If your device or adapter gets wet, carefully unplug all cables without getting your hands wet, and wait for the device and adapter to dry completely before plugging them back in. Do not try to dry your device or adapter with an external heat source, such as a microwave oven or blow dryer. If the device or adapter is damaged, stop using it immediately. Use only the supplied accessories to power your device. To avoid the risk of electric shock, do not touch the device or the cables connected to it during a thunderstorm. The cables and/or adapters are only designed for indoor use.

Legal notice: PingOc Now SL is not responsible for the fraudulent or erroneous use of the product due to the lack of understanding or reading of the information in the instructions and precautions. This product is not a toy and must not be used contrary to current applicable laws. If you have any questions you can contact us before using the product.

For EU customers: Hereby, PingaOculto, declares that the type of radio equipment is in accordance with Directive 2014/53/EU.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

FCC Compliance: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet the general RF exposure requirement. The device can be used in portable exposure conditions without restrictions.

Radio Frequency Exposure Compliance: As a health protection measure, this device complies with the limits for exposure of the general public to electromagnetic fields in accordance with council recommendation 1999/519/EC. This device can be placed on the body avoiding prolonged use of it for more than 5 hours.

How to recycle your device properly: Disposal of certain electronic devices is regulated in some areas. Make sure you comply with local regulations and laws.

Additional Safety and Compliance Information: For additional information on safety, recycling and compliance or other important issues related to your device, do not hesitate to contact us through any of the available means of contact. Means of contact with: Email contact@pingaoculto.com, Call/WhatsApp +34 644 098 320.

Limited Warranty: All official brand items PingaOculto have 2 year minimum warranty. This guarantee may be extended or reduced depending on the country where the sale takes place, as is the case by law in Spain where it is extended to 3 years as established by Decree-Law 7/2021 with respect to the Guarantee on the Sale of Goods. of consumption. We reserve the right to deny the guarantee of a product if improper or negligent use by the client is verified, similar to those reflected in: https://www.pingaoculto.es/garantias-y-devoluciones/ If you need to contact us due to a failure, you can do so by email: contact@pingaoculto.com or by Call/WhatsApp: +34 644 098 320.

Find Out More

Do you want to contact us?

follow us on